Learning Paths Subscription Courses

ADS RFPro Fundamentals

Course 3 of 3 in Get Started with ADS and RFPro

Learn how to simulate ADS layouts in RFPro using Momentum and FEM solvers

Register for the learning path to register for this course

About this course

 
+ Learning Objectives

This course will give you an overview of the fundamentals of needed to work with RFPro to perform electromagnetic simulations

  • RFPro Introduction
    • Learn the basics to get started with RFPro
    • Lab 1: You will start with a LPF design, add the layout interconnects, prepare the layout for processing in RFPro, run Momentum simulation, investigate the S-parameter results in RFPro, generate a schematic for ADS to run a Circuit-EM co-simulation
  • Working with RFPro Simulator
    • Learn the different parts of the RFPro simulator needed to fully utilize the EM simulation.
    • Lab 2: You will work on the evaluation board, instead of simulating the entire layout, you select just the Nets of interest in a User Defined EM simulation. You will set different kinds of virtual pins in RFPro.
  • Going In-Depth with RFPro
    • Working with components and advanced technologies inside of RFPro
    • Lab 3: We introduce the concept of Smart Mount, combine different designs having different technologies in one complete EM simulation and then run a Circuit-EM co-simulation.
+ Content Types
  • Video Lessons
  • Hands-on Labs
  • Knowledge Check
+ Who should take this course?
  • Design engineers
+ Prerequisites

 

 

Curriculum7.5 hr

  • Session 1
  • RFPro Introduction 18 min
  • Lab 1-Low-Pass Filter Design 120 min

    We start with a LPF design, add the layout interconnects, prepare the layout for processing in RFPro, run Momentum simulation, investigate the S-parameter results in RFPro, generate a schematic for ADS to run a Circuit-EM co-simulation

  • Session 2
  • Working with the RFPro Simulator 17 min
  • Lab 2- EM Model Extraction of ADI Eval Board 120 min

    You will work on the evaluation board, instead of simulating the entire layout, you select just the Nets of interest in a User Defined EM simulation. You will set different kinds of virtual pins in RFPro.

  • Session 3
  • Going In-Depth with RFPro 17 min
  • Lab 3-Mixed-Technology Design in RFPro 120 min

    We introduce the concept of Smart Mount, combine different designs having different technologies in one complete EM simulation and then run a Circuit-EM co-simulation.

  • Summary and Next Step
  • Knowledge Check 20 min
  • Claim your Certificate

About this course

 
+ Learning Objectives

This course will give you an overview of the fundamentals of needed to work with RFPro to perform electromagnetic simulations

  • RFPro Introduction
    • Learn the basics to get started with RFPro
    • Lab 1: You will start with a LPF design, add the layout interconnects, prepare the layout for processing in RFPro, run Momentum simulation, investigate the S-parameter results in RFPro, generate a schematic for ADS to run a Circuit-EM co-simulation
  • Working with RFPro Simulator
    • Learn the different parts of the RFPro simulator needed to fully utilize the EM simulation.
    • Lab 2: You will work on the evaluation board, instead of simulating the entire layout, you select just the Nets of interest in a User Defined EM simulation. You will set different kinds of virtual pins in RFPro.
  • Going In-Depth with RFPro
    • Working with components and advanced technologies inside of RFPro
    • Lab 3: We introduce the concept of Smart Mount, combine different designs having different technologies in one complete EM simulation and then run a Circuit-EM co-simulation.
+ Content Types
  • Video Lessons
  • Hands-on Labs
  • Knowledge Check
+ Who should take this course?
  • Design engineers
+ Prerequisites

 

 

Curriculum7.5 hr

  • Session 1
  • RFPro Introduction 18 min
  • Lab 1-Low-Pass Filter Design 120 min

    We start with a LPF design, add the layout interconnects, prepare the layout for processing in RFPro, run Momentum simulation, investigate the S-parameter results in RFPro, generate a schematic for ADS to run a Circuit-EM co-simulation

  • Session 2
  • Working with the RFPro Simulator 17 min
  • Lab 2- EM Model Extraction of ADI Eval Board 120 min

    You will work on the evaluation board, instead of simulating the entire layout, you select just the Nets of interest in a User Defined EM simulation. You will set different kinds of virtual pins in RFPro.

  • Session 3
  • Going In-Depth with RFPro 17 min
  • Lab 3-Mixed-Technology Design in RFPro 120 min

    We introduce the concept of Smart Mount, combine different designs having different technologies in one complete EM simulation and then run a Circuit-EM co-simulation.

  • Summary and Next Step
  • Knowledge Check 20 min
  • Claim your Certificate
​

Ready to Get Started?

CONTACT SALES