ADS RFPro Fundamentals

Learn how to simulate ADS layouts in RFPro using Momentum and FEM solvers

Cancel Apply

rate limit

Code not recognized.

About this course

 
+ Learning Objectives

This course will give you an overview of the fundamentals of needed to work with RFPro to perform electromagnetic simulations

  • RFPro Introduction
    • Learn the basics to get started with RFPro
    • Lab 1: You will start with a LPF design, add the layout interconnects, prepare the layout for processing in RFPro, run Momentum simulation, investigate the S-parameter results in RFPro, generate a schematic for ADS to run a Circuit-EM co-simulation
  • Working with RFPro Simulator
    • Learn the different parts of the RFPro simulator needed to fully utilize the EM simulation.
    • Lab 2: You will work on the evaluation board, instead of simulating the entire layout, you select just the Nets of interest in a User Defined EM simulation. You will set different kinds of virtual pins in RFPro.
  • Going In-Depth with RFPro
    • Working with components and advanced technologies inside of RFPro
    • Lab 3: We introduce the concept of Smart Mount, combine different designs having different technologies in one complete EM simulation and then run a Circuit-EM co-simulation.
+ Content Types
  • Video Lessons
  • Hands-on Labs
  • Knowledge Check
+ Who should take this course?
  • Design engineers
+ Prerequisites

 

 

Curriculum7.5 hr

  • Session 1
  • RFPro Introduction 18 min
  • Lab 1-Low-Pass Filter Design 120 min

    We start with a LPF design, add the layout interconnects, prepare the layout for processing in RFPro, run Momentum simulation, investigate the S-parameter results in RFPro, generate a schematic for ADS to run a Circuit-EM co-simulation

  • Session 2
  • Working with the RFPro Simulator 17 min
  • Lab 2- EM Model Extraction of ADI Eval Board 120 min

    You will work on the evaluation board, instead of simulating the entire layout, you select just the Nets of interest in a User Defined EM simulation. You will set different kinds of virtual pins in RFPro.

  • Session 3
  • Going In-Depth with RFPro 17 min
  • Lab 3-Mixed-Technology Design in RFPro 120 min

    We introduce the concept of Smart Mount, combine different designs having different technologies in one complete EM simulation and then run a Circuit-EM co-simulation.

  • Summary and Next Step
  • Knowledge Check 20 min
  • Claim your Certificate

About this course

 
+ Learning Objectives

This course will give you an overview of the fundamentals of needed to work with RFPro to perform electromagnetic simulations

  • RFPro Introduction
    • Learn the basics to get started with RFPro
    • Lab 1: You will start with a LPF design, add the layout interconnects, prepare the layout for processing in RFPro, run Momentum simulation, investigate the S-parameter results in RFPro, generate a schematic for ADS to run a Circuit-EM co-simulation
  • Working with RFPro Simulator
    • Learn the different parts of the RFPro simulator needed to fully utilize the EM simulation.
    • Lab 2: You will work on the evaluation board, instead of simulating the entire layout, you select just the Nets of interest in a User Defined EM simulation. You will set different kinds of virtual pins in RFPro.
  • Going In-Depth with RFPro
    • Working with components and advanced technologies inside of RFPro
    • Lab 3: We introduce the concept of Smart Mount, combine different designs having different technologies in one complete EM simulation and then run a Circuit-EM co-simulation.
+ Content Types
  • Video Lessons
  • Hands-on Labs
  • Knowledge Check
+ Who should take this course?
  • Design engineers
+ Prerequisites

 

 

Curriculum7.5 hr

  • Session 1
  • RFPro Introduction 18 min
  • Lab 1-Low-Pass Filter Design 120 min

    We start with a LPF design, add the layout interconnects, prepare the layout for processing in RFPro, run Momentum simulation, investigate the S-parameter results in RFPro, generate a schematic for ADS to run a Circuit-EM co-simulation

  • Session 2
  • Working with the RFPro Simulator 17 min
  • Lab 2- EM Model Extraction of ADI Eval Board 120 min

    You will work on the evaluation board, instead of simulating the entire layout, you select just the Nets of interest in a User Defined EM simulation. You will set different kinds of virtual pins in RFPro.

  • Session 3
  • Going In-Depth with RFPro 17 min
  • Lab 3-Mixed-Technology Design in RFPro 120 min

    We introduce the concept of Smart Mount, combine different designs having different technologies in one complete EM simulation and then run a Circuit-EM co-simulation.

  • Summary and Next Step
  • Knowledge Check 20 min
  • Claim your Certificate
​

Ready to Get Started?

CONTACT SALES